The AiM
PDM08 is a power distribution module that replaces conventional fuse and relay systems. It has 8 power outputs with different power levels. With the integrated data recording, the 6 analogue/digital and 2 speed inputs can be recorded.
Two of the three CAN interfaces can be connected to over 2,000 ECUs from the industry's leading ECU manufacturers. AiM extensions such as GPS, SmartyCam, etc. are connected to the third CAN interface. The
PDM08 can be connected to a 6" or 10" TFT display via the Lin Bus. As the 10" display does not have its own buttons, the Remote Control Module should also be used.
All this is housed in an IP65 splash-proof aluminium housing.
CAN-Bus Technology
Special features PDM08
- 1 switching output up to 25 A
- 1 switching output up to 20 A
- 6 switching output up to 15 A
- 6 Analog-/Digital inputs
- 2 Speed inputs
- Total power 100 A
- 4 GB Storage
- 3 CAN interfaces
- ECU Interface (CAN, RS232)
Connection example AiM PDM08
Technical Data AiM PDM08
| Rev counter |
Tapping from the control unit CAN/RS 232
Indication area 0 up to 22.000 rpm |
| Time measurement |
Triggerung over CAN-Optical-Beacon or GPS
Lap times without Limit, up to 5 split times
Measuring accuracy 1/100 sec. |
| Analog channels |
6 inputs (0-5 V, 12 bit)
with switchable 2 kOhm pull-up resistor |
| Switching outputs |
1 switching output up to 25 A
1 switching output up to 20 A
6 switching output up to 15 A |
| Total power |
100 A |
| Speed |
2 digital inputs
Acquisition via inductive wheel sensor ABS, CAN/RS232 or GPS
Indication in km/h or mph
Sampling rate 10 - 100 Hz, free arbitrary |
| Acceleration |
triaxial ± 5 g and Gyroscope im Logger integrated
Sampling rate acceleration sensor 1 - 100 Hz, free arbitrary
Sampling rate Gyroscope 1 - 50 Hz, free arbitrary |
| Total sampling rate |
8950 Hz (without ECU) |
| Connector |
AMP 35 pin, black
Binder 711. 3-pin
Amphenol
Rosenberger LVDS |
| Additional function |
Rear camera input
2 digital inputs
calculated channels |
| Data storage |
non volatile 4 GB-storage |
| Data transfer |
USB |
| Power supply |
over 12V on-board power supply
In / Out over ignition switch
no data loss after switching off |
| Updates |
Software- and Firmware updates for free over the internet |
| Measurement |
161 x 100,6 x 50,6 mm |
| Weight |
370 gr |
The inputs on the PDM08
 |
| 1 |
AMP connector 34-pin, black |
2 |
Amphenol connection to the battery |
3 |
Status LED's |
| 4 |
USB connection between PC and PDM |
5 |
Display connection LVDS |
|
|
AiM RaceStudio3 Software for PDM08
RaceStudio3 is the Software for the current generation of the AiM Logger.
This software can be used to create configurations and transfer them to the unit via USB. The measured values can be checked via an online mode or a recording can be started manually.
With RS3, mathematical channels can now also be created, transmitted to the unit and shown on the display.
Expensions for PDM08
Accessory for PDM08
 |
 |
 |
 |
 |
 |
 |
| Fastener syst. |
Temperature |
Movement |
Pressure |
Speed |
Data Hub |
Cable |
 |
 |
|
|
|
|
|
| Lap time |
Connectors |
|
|
|
|
|
Overview of the Power Distribution Module
|
 |
 |
| PDM32 | PDM08 |
|---|
| Supply |
| Power supply |
9 - 15 VDC |
9 - 15 VDC |
| Power consumption mA (max.) |
450 |
450 |
| Inputs |
| Analog [optional] |
8 [40] |
6 [40] |
| Analog 0 - 5 V |
x |
x |
| Analog 0 - 12 V |
x |
x |
| ECU Channels [max.] |
120 |
120 |
| Digital [optional] |
14 [24] |
8 [24] |
| Thermocouple [optional] |
- [40] |
- [40] |
| Speed |
2 |
2 |
| Lap time GPS |
x |
x |
| Lap time optical |
- |
- |
| Lap time magnetic |
- |
- |
| Rear camera |
2 |
- |
| External Keyboard |
o [RBI] |
o [RBI] |
| RPM over coil |
o |
o |
| Outputs |
| Signal / Digital |
32 |
8 |
| CAN |
2 |
2 |
| Reference voltage |
5V |
5V |
| Communication |
| CAN Interface |
3 |
3 |
| K-Line |
1 |
1 |
| RS232 |
1 |
1 |
| USB |
x |
x |
| WiFi |
- |
- |
| Storage |
| Storage in GB [optional] |
4 [32] |
4 [32] |
| Total sample rate |
8950 |
8950 |
| Sample rate per channel |
up to 1.000 Hz |
up to 1.000 Hz |
| Other |
| Acceleration sensor |
- |
- |
| Gyroscope |
- |
- |
| Connector |
2x AMP 35-p, Binder 711 3-/5-p, Amphenol, Rosenberger |
2x AMP 35-p, Binder 711 3-p, Amphenol, Rosenberger |
| MOT |
o |
o |
| Display |
- |
- |
| Alarm lights |
- |
- |
| Shift lights |
- |
- |
| Calculated channels |
x |
x |
| Light sensor |
- |
- |
| Measurements |
234,5 x 94,6 x 49,5 mm |
161 x 100,6 x 50,6 mm |
| Weight |
761 gr |
370 gr |
| Protection class |
IP65 |
IP65 |
| Expansion |
| GPS |
o |
o |
| Lambda |
o |
o |
| Displays |
o |
o |
| SmartyCam |
o |
o |
| TC-Hub |
10 |
10 |
| Channel Expansion / ACC |
10 |
10 |
| Shift Light Module |
o |
o |
| Memory Module |
o |
o |
| Remote Buttons Interface |
o |
o |
| RIO02 |
o |
o |
x = standard | o = optional | - = not possible | Digit = amount