The
AiM MXPS is a 6" TFT display with data recording for Suzuki GSX-R 1000 R motorbikes. It has 10 configurable RGB shift lights and a WiFi connection. The kit comes with an optional GPS module to get lap times and many other important information.
The
MXPS is equipped with a JAE main connector for plug&play connection to the Suzuki GSX-R 1000 and GSXR-R 1000 R models 2017-2022. The 5-pin 711 connector can be used to connect extensions such as the GPS module, a channel expansion, TC Hub, SmartyCam or Lambda Controller.
The sturdy aluminium housing meets the requirements of protection class IP65, making the
MXPS suitable for the Suzuki. The integrated buttons can be used to adjust the settings of the
AiM MXPS and switch between the configured pages. You can also choose between street mode and race mode.
CAN-Bus Technology
Special features MXPS
- 4 freely configurable analogue inputs
- 10 RGB Shift-lights
- 9 Icons
- Lap times with up to 5 split times
- WiFi connection
- 4 GB storage
- 3 CAN interface
- ECU Interface (CAN and K-Line)
- Input for rear camera
Connection example AiM MXPS
Technical Data AiM MXPS
| Rev counter |
Tapping from the control unit via the JAE 32 pin connector |
| Time measurement |
Triggering via GPS
Lap times without limit, up to 5 split times
Measurement accuracy 1/100 sec.
Lap time prediction |
| Analogue channels |
4 inputs (0-5 V, 12 bit)
Thermocouple 0 -1200°C, measuring accuracy + 0.75% optionally with a TC Hub
Thermocouple resistance up to 180 °C, measuring accuracy + 1°
9 Icons, when the set alarm values are exceeded or not reached
Display in °C or °F
Sampling rate 1 - 200 Hz, freely selectable depending on sensor type
Day and total odometer |
| Speed |
Acquisition from the control unit via the JAE 32 pin connector
Display in km/h or mph |
| Calculations |
Possible with mathematical channels |
| Gear indicator |
Via the CAN stream directly from the ECU |
| Total sampling rate |
8950 Hz (without ECU) |
| Connector |
1x JAE 32 pin
2x Binder 711 5 pin
1x Binder 711 3 pin
1x Binder 711 8 pin |
| Shift light |
10 freely configurable RGB LEDs
Freely configurable for each aisle |
| Additional function |
Display of the difference to the fastest lap in the split times
Lap time prediction
Wifi connection
Light sensor for display illumination |
| Data storage |
Non-volatile 4 GB memory |
| Data transfer |
WiFi 802.11 or USB |
| Power supply |
via 12V on-board power supply
On / Off via ignition switch
No data loss after switching off |
| Updates |
Software and firmware updates free of charge via the Internet |
| Measurements |
Housing: 189,6 x 106,4 x 24,9 mm
Display: 139,1 x 78,5 mm |
| Weight |
620 gr |
The functions of MXPS
 |
| 1 |
9 Icons |
2 |
10 RGB shift lights, free configurable |
3 |
Display pages, free configurable |
| 4 |
Windows for information |
5 |
Light-sensor for illumination |
6 |
4 Display Buttons with various functions |
The connections of MXPS
 |
| 1 |
3x fixing points |
2 |
Binder 711 8 pin, SDS + analogue channel |
3 |
Binder 711 5 pin, mirror camera |
| 4 |
Binder 711 3 pin, USB |
5 |
Binder 5 pin, Expansion |
6 |
JAE 32 pin, harness |
Channels over CAN-Bus
| RPM |
Speed |
| Intake air temperature |
Fuel sensor percentage |
| Neutral |
ABS warning |
| Oil pressure status |
Fuel used |
| Speed ABS |
Water temperature |
| Gear |
Fuel flow |
| SDMS Mapping |
Launch control active |
| Fuel economy |
Fuel consumption |
| Speed on Dash |
Fuel Level |
| TC level |
TC |
| Fuel Range |
ABS Data OK |
| Accelerations |
IMU Data OK |
| SDS2 Data OK |
LED TC |
Channels over SDS (optional wiring harness)
| Analog 1 |
Analog 2 |
| Analog 3 |
Analog 4 |
| Speed front |
Speed rear |
| Battery voltage |
Water temperature |
| Intake air temperature |
Airbox pressure |
| Barometric pressure |
Fuel injector 1-4 |
| Ignition angle 1 - 4 |
TPS voltage |
| Grip voltage |
Gear sensor |
| TPS |
Grip position |
| Wheel spin rate with TC OFF |
Wheel Spin rate with TC ON |
| Dash pot correction angle |
SPS Status OK |
The Display AiM MXPS
The free configurable 6“ TFT olor display of the MXPS has a contrast of 600:1 and a brightness of 700 cd/m² e.g. 1,100 lumen. Over a light-sensor the contrast and the brightness are continuously adjusted to the surrounding. Whether various display pages, warning messages or mathematical channels, all this can be shown on the display.
WiFi connection
Over the secure 802.11 WiFi connection the AiM MXPScan in conjunction with the RaceStudio3 be configured, calibrated or the data can be downloaded.
AiM RaceStudio3 Software for MXPS
RaceStudio3 is the software for the new generation of AiM loggers.
With this software, configurations can be created and transferred to the device via Wi-Fi or USB. The measured values can be checked via an online mode or a recording can be started manually.
Accessory for AiM MXPS
 |
 |
 |
 |
 |
 |
 |
| Movement |
Data Hub |
Temperature |
Pressure |
Speed |
Cables |
Connectors |
Overview of the TFT Dash logger