AiM ECULog is a compact data logger that records channels coming from the engine control unit via CAN Bus, RS232 or OBDII. This data are stored in the internal 4 GB memory and, when connected, also on a 16 GB USB-C stick. Due to it's small size it can also be used on a motocross, supermoto or enduro.
The ACC2, Lambda, GPS or SmartyCam 3 can be connected via the internal AiM CAN Bus.
CAN-Bus Technology
Features ECULog
- 4 GB storage (expandable on up to 16 GB)
- 2 CAN interfaces
- ECU Interface (CAN-Bus ,RS232, K-Line and OBDII)
Connection example AiM ECULog
Technical data AiM ECULog
| Tachometer |
Tapped from CAN/RS 232/OBDII |
| Time measurement |
Triggered by GPS
Lap times without limit, up to 5 intermediate times
Accuracy of measurement: 1/100 sec. |
| Connector |
1x Binder 711, 7-pin
1x Binder 711, 5-pin
1x USB-C |
| Data memory |
non-volatile 4 GB memory |
| Data transfer |
USB-C |
| Power supply |
over 12 V main power supply
ignition switch for on and off
no data loss after switching off |
| Updates |
Software- and Firmware updates gratis on the Internet |
| Admeasurements |
61.4 x 44.7 x 27.2mm |
| Weight |
100 gr. |
| Protection class |
IP65 |
Inputs on the ECULog
 |
| 1 |
Input USB-C |
2 |
Input for Binder 711, 7-pin |
3 |
Input for Binder 711, 5-pin |
| 4 |
Fixing points |
|
|
|
|
Highlights AiM ECULog
 |
 |
 |
Housing
The AiM ECULog has a black glass fiber reinforced PA6 housing.
|
Software | RaceStudio3
With RaceStudio3 the ECULog can be configured, the recorded data can be downloaded and analyzed.
|
Connectors
The ECULog has a Binder 711-7 pin connector for ECU as well as a Binder 711 5-pin for the expansions.
|
| |
|
|
 |
 |
|
USB connection
The ECULog can be configured, calibrated or the data downloaded in conjunction with RaceStudio3 viaUSB-C connection.
|
USB-C Stick
The recorded data could be als stored on a USB-C stick.
|
|
| |
|
|
Expansions for ECULog
RaceStudio 3 AiM ECULog
 |
 |
 |
Channels
ECULog hasn't own analog / digital channels, but you can do some settings under the channels.
|
ECU Stream
ECU Streams from over 2.000 manufacturers are now stored in RaceStudio 3. Select them and send it to the ECULog. |
Expansions
The respective Expansion for the AiM ECULog can be selcted and configred.
|
| |
|
|
 |
 |
 |
Math. channels
The calculation for math. channels is configured in RaceStudio 3 and can be logged on ECULog.
|
Status variables
The status variables can be used to create a channel that displays 0 or 1 via various conditions. This can be used to create diagnostic channels. |
Analysis
All downloaded data is stored in RaceStudio 3 analysis. Everything from time/distance, X/Y plot to the data report can be freely set.
|
| |
|
|
Accessory for ECULog
 |
 |
 |
 |
 |
 |
 |
| Mounting |
Acceleration |
Movement |
RPM |
Pressure |
Speed |
Hubs |
 |
 |
 |
 |
|
|
|
| Cable |
Lap time |
Connector |
Temperature |
|
|
|